Dlask Arms Corps.  XB-5. By far our most popular linear compensator in stainless steel. Threaded for 1/2″ x 28 tpi with a .25″ exit hole (.22 lr /.223,etc.) These not only make your rifle stand out in a crowd but also serve to direct the gasses following the bullet away from the round as it exits the muzzle, improving accuracy.

Comes in your choice of a matte stainless finish or polished stainless finish.

The post Dlask Arms XB-5 Linear Compensator / Muzzle Brake, Stainless Steel appeared first on Dlask Arms Corp..

KIDD Magazine Latch Plunger, Stainless Steel + Spring

Replace your factory magazine latch plunger with a new stainless steel version of KIDD Magazine Latch Plunger. With upgraded geometry to both hold your magazine more stable and let it release easier.

The post KIDD Magazine Latch Plunger, Stainless Steel + Spring appeared first on Dlask Arms Corp..

The ol’ reliable Vang Comp Stainless Steel Magazine Follower. These are turned from a solid piece of stainless steel bar-stock. This multitasking replacement for your factory-installed magazine follower not only travels smoother in your magazine tube due to it’s reduced bearing surface but it actually collects dirt and debris from the inside of your magazine, thus making it easier for you to clean your gun.

The post Vang Comp Remington 870 Follower, Stainless Steel appeared first on Dlask Arms Corp..

Extra long oversize 1911 Release Button features 40 lpi checkering for positive grip and increased length for faster easier mag changes with little or no change in grip.

1911 PARTS LIST

The post Dlask 1911 Release Button – Extra Long Oversize appeared first on Dlask Arms Corp..

Dlask 1911 Bobtail Mainspring Housing – Reduce the Bulk For Concealed Carry Guns. Eliminates the sharp profile at the rear of the grip that can print when carrying a concealed 1911 Auto. Reduces bulk without reducing magazine capacity or performance. Removes nearly 1/2″ of material from the butt while maintaining correct grip position. Will require modification of grip panels. Installation Jig gives precise location of mainspring hole.

1911 PARTS LIST

The post Dlask 1911 Bobtail Mainspring Housing appeared first on Dlask Arms Corp..

Dlask 1911 Recoil Springs are carefully wound and heat-treated from the finest ordnance-spec music wire to give you long-lasting durability and resistance to heat and deformation over time.  They have been thoroughly tested and will maintain a consistent spring weight during long-term use. Springs will fit Commander Colt 1911 length pistols and clones, including models from Para Ordnance, Kimber and Springfield Armory.

The post Dlask 1911 16lb Recoil Spring for Commander with Firing Pin Spring appeared first on Dlask Arms Corp..

Dlask 1911 Recoil Spring – Carefully wound and heat-treated from the finest ordnance-spec music wire to give you long-lasting durability and resistance to heat and deformation over time.  They have been thoroughly tested and will maintain a consistent spring weight during long-term use. Springs will fit Colt 1911 length pistols and clones, including models from Para Ordnance, Kimber and Springfield Armory. These pistols all have 5″ long slides.

The post Dlask 1911 16lb Recoil Spring, 5″ Government with Firing Pin Spring appeared first on Dlask Arms Corp..

Dlask 1911 Slide Stop – 9mm and .38 super – Pin is machined to maximum dimensions for a tighter lockup and increased accuracy. Oversize lip gives positive, last round engagement. Fits all 9mm and .38 super 1911 Autos, including high-capacity. Specially heat-treated steel gives unlimited service.

1911 PARTS LIST

The post Dlask 1911 Slide Stop – 9mm and .38 super, Hardcore, Stainless, Carbon Steel appeared first on Dlask Arms Corp..

Dlask 1911 Slide Stop .45 ACP – Pin is machined to maximum dimensions for a tighter lockup and increased accuracy. Oversize lip gives positive, last round engagement. Fits all .45 ACP 1911 Autos, including high-capacity. Specially heat-treated steel gives unlimited service.

1911 PARTS LIST

The post Dlask 1911 Slide Stop .45 ACP Auto, Hardcore, Stainless, Carbon Steel appeared first on Dlask Arms Corp..

Drops right onto 1911 Officer ACP frames without gun smithing. The separate magazine well can be removed without disassembling the pistol. Enlarged magwell greatly increases frame opening for faster and easier magazine changes. Flat housing increases grip surface area to help keep the pistol from riding up during firing. Available with 25 lines-per-inch checkering that helps keep the pistol centered in your grip.

The post Dlask 1911 Officer ACP Drop in Mag-Well, Stainless Steel appeared first on Dlask Arms Corp..